Binks M1-G HVLP User Manual download pdf

Service Bulletin

SBBI-2-181-D

Replaces SBBI-2-181-C

Repair Kit 54-4367-1

M1-G HIGH VOLUME LOW PRESSURE (HVLP)

GRAVITY FEED SPRAY GUN

TABLE OF CONTENTS

PG. SECTION

1 Description

1 Installation & Assembly

2 Safety Precautions

3 Operation

3 Cup Cleaning

3 Gun Cleaning & Lubrication

3 Parts Replacement

4 Parts List, Gun

5 Parts List, Cup

6 Troubleshooting

7 Troubleshooting

8 Accessories

IMPORTANT: Before using this

equipment, read all safety precau-

tions on page 2 and instructions.

Keep for future use.

DESCRIPTION, GUN

The high volume low pressure gravity

feed M1-G guns are designed to apply a

wide variety of finishing materials.

These guns were manufactured to

provide a maximum transfer efficiency

by limiting air cap pressure to 10 psi

(complies with rules issued by SCAQMD

and other air quality authorities).

These guns will produce approxi-

mately 10 psi air cap pressure at the

recommended gun inlet pressure.

Air cap test kits are available (see

Accessories) which can be utilized to

set the exact air cap pressure.

DESCRIPTION, CUP

This cup is designed to be used with

or without the disposable cup liner.

The cup liner allows painting in any

position and simplifies clean up.

This gravity feed cup is designed to

work with the M1-G gravity feed spray

guns. The cup is constructed from

durable aluminum to provide trouble-

free operation. The cup fluid fitting is

electroless nickel plated brass. The

disposable cup lid is recyclable and is

constructed with recycled polyeth-

ylene. The lid has a unique drip check

to prevent paint from dripping out of

the vent in the lid.

Halogenated Hydrocarbon

Solvents—for example: 1, 1,

1-trichloroethane and methy-

lene chloride can react with the

aluminum in this cup and cause

an explosion hazard. Read the

data sheet for the material you

intend to spray. Do not use

spray materials containing

these solvents with this cup.

INSTALLATION

NOTE

Protective coating and rust

inhibitors have been used to

keep the gun and cup in good

condition prior to shipment.

Before using, flush with solvents

so that these materials will be

removed from fluid passages.

For maximum transfer efficiency, do

not use more pressure than is neces-

sary to atomize the material being

applied.

1. Connect the gun to a clean, mois-

ture and oil free air supply using a

hose size of at least 5/16" I.D. hose.

Do not use 1/4" I.D. hose.

NOTE

When gun is triggered on,

adjust regulated pressure to

desired setting to provide a

maximum of 10 psi at the air

cap. Do not use more pressure

than is necessary to atomize

the material being applied.

Excessive pressure will create

additional overspray and reduce

transfer efficiency.

NOTE

If quick connects are required,

use ONLY high flow quick

connects approved for HVLP use,

such as HC-4419 and HC-4719.

Other types will not flow enough

air for proper gun operation.

NOTE

If an air adjusting valve is used at

the gun inlet, use Model HAV-500

or HAV-501. Some competitive

adjusting valves have significant

pressure drop that can adversely

affect spray performance. Models

HAV-500 and HAV-501 have

minimal pressure drop, which is

important for HVLP spraying.

2. Attach the gravity feed cup to the

material inlet.

ASSEMBLY OF CUP TO GUN

1. Install one of the blue cup gaskets.

2. Place this cup gasket in the fluid

inlet of the gun body.

3. Place filter in

cup outlet at

this time if

desired.

4. Assemble

cup to gun

and tighten

hand tight.

FILLING WITH PAINT

Fill the cup with paint to the full mark.

DO NOT OVERFILL.

INSTALLING THE LID

Place plastic lid on the top of the cup,

and push in the center of the lid to

assemble lid. Fold vent cap and push

onto center portion of lid (if vent cap is

not already assembled).

GUN GUN FLUID NOZZLE AIR NOZZLE FLUID NEEDLE

ASSEMBLY INLET MARKINGS PART NO. MARKINGS PART NO. MARKINGS PART NO.

6924-0000-0 18 PSI 94 (1.4mm) 45-9400 93P 46-9300 ABSS 54-4382

Drain Hole

Cup Fitting

Filter

Cup

Gasket

Gun Body

Continued on Page 3

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - GRAVITY FEED SPRAY GUN

Service BulletinSBBI-2-181-DReplaces SBBI-2-181-CRepair Kit 54-4367-1M1-G HIGH VOLUME LOW PRESSURE (HVLP) GRAVITY FEED SPRAY GUNTABLE OF CONTENTS PG.

Page 2 - Page 2 SBBI-2-181-D

Page 2 SBBI-2-181-DImportant information that tells how toprevent damage to equipment, or howto avoid a situation that may cause mi-nor inju

Page 3

Page 3 SBBI-2-181-DOPERATIONTurn on air supply and set gun inlet pressure to lowest recommended pressure for material being sprayed. Best atomizat

Page 4 - M1-G HVLP GRAVITY FEED GUN

Page 4 SBBI-2-181-D Order Parts No. No. Description Required 1 54-3531 Retaining Ring (For 92P and 93P Air Nozzle) 1 2 46-9300 Air

Page 5 - 702576 900 cc ALUMINUM cUP

Page 5 SBBI-2-181-D702576 900 cc ALUMINUM cUP Ref. Replacement No. Part No. Description 702576 Metal Gravity Feed Cup* 1 GFC-404-K2 D

Page 6 - Page 6 SBBI-2-181-D

Page 6 SBBI-2-181-DBalance air pressure and fluid flow. Increasespray pattern width with spreader adjustmentvalve.Thin or lower fluid flow.Adj

Page 7 - Page 7 SBBI-2-181-D

Page 7 SBBI-2-181-DFluid dripping or leaking frombottom of cupRuns and sagsThin, sandy coarse finish dryingbefore it flows outThick, dimpled finis

Page 8 - Automotive Refinishing

Page 8 SBBI-2-181-DACCESSORIESGFC-501 (Acetal) 20 oz.702576 (Aluminum) 900 ccGravity Feed CupsHAV-500 or HAV-501 (shown) Adjusting ValveHAV-50

Binks M1-G HVLP User Manual

Browse online or download User Manual for Paint Sprayer Binks M1-G HVLP. SBBI-2-181-D M1-G HIGH VOLUME LOW PRESSURE

Summary of Contents

More documents for Paint Sprayer Binks M1-G HVLP

Comments to this Manuals

Binks M1-G HVLP User Manual

Browse online or download User Manual for Paint Sprayer Binks M1-G HVLP. SBBI-2-181-D M1-G HIGH VOLUME LOW PRESSURE

Summary of Contents

More documents for Paint Sprayer Binks M1-G HVLP

Comments to this Manuals

Related products and manuals for Paint Sprayer Binks M1-G HVLP